FH Upper AustriaResearch & Development

Materials and Production Engineering Research Center Wels Campus

Publications

Heat Treating of Cold-Work Tool Steels - Low- and Un-Alloyed Water and Oil Hardening Steels

R. Mesquita, R. Schneider, C. Sales Goncalves - Heat Treating of Cold-Work Tool Steels - Low- and Un-Alloyed Water and Oil Hardening Steels in Heat Treating of Irons and Steels Vol 4D, 2014, pp. 320-328
  • Book
  • Materials and Production Engineering

Heat Treating of Cold-Work Tool Steels - Medium-Alloy air Hardening, High Carbon High Chromium and High Vanadium-Powder Metallurgy Steels

R. Mesquita, R. Schneider, C. Sales Goncalves - Heat Treating of Cold-Work Tool Steels - Medium-Alloy air Hardening, High Carbon High Chromium and High Vanadium-Powder Metallurgy Steels in Heat Treating of Irons and Steels Vol 4D, 2014, pp. 329-335
  • Book
  • Materials and Production Engineering

Heat Treating of Hot-Work Tool Steels

R. Mesquita, R. Schneider, C. Sales Goncalves - Heat Treating of Hot-Work Tool Steels in Heat Treating of Irons and Steels Vol 4D, 2014, pp. 336-346
  • Book
  • Materials and Production Engineering

Heat Treating of High-Speed Tool Steels

R. Mesquita, R. Schneider, C. Sales Goncalves - Heat Treating of High-Speed Tool Steels in Heat Treating of Irons and Steels Vol 4D, 2014, pp. 347-357
  • Book
  • Materials and Production Engineering

Heat Treating of Mold Steels and Corrosion-resistant Tool Steels

R. Mesquita, R. Schneider, C. Sales Goncalves - Heat Treating of Mold Steels and Corrosion-resistant Tool Steels in Heat Treating of Irons and Steels Vol 4D, 2014, pp. 358-362
  • Book
  • Materials and Production Engineering

Comparing investigation on the hardness-toughness relationship of the steels 42CrMo4, 51CrV4, 55Cr3 and 100Cr6 in the area of blue brittleness

M. Auer, K. Steineder, R. Schneider, M. Klein - Comparing investigation on the hardness-toughness relationship of the steels 42CrMo4, 51CrV4, 55Cr3 and 100Cr6 in the area of blue brittleness - Proceedings of the Härtereitagung 2013, Wien, Austria, 2013
This work deals with the effect of conventional hardening on the mechanical properties hardness and toughness of the engineering steels 42CrMo4, 51CrV4, 55Cr3…   mehr
  • Proceedings
  • Materials and Production Engineering

Investigation of the hardness-toughness-relationship of a welded joint after different heat-treatment cycles

T. Schlagradl, R. Schneider, G. Posch, R. Schnitzer - Investigation of the hardness-toughness-relationship of a welded joint after different heat-treatment cycles - Welding in the World, Vol. 57, No. 1, 2013, pp. 113-121
  • Journal
  • Materials and Production Engineering

Evolution and formation of microstructures of structural steels with higher Mn-contents

M. Aigner, R. Schneider, E. Arenholz, L. Samek - Evolution and formation of microstructures of structural steels with higher Mn-contents - Proceedings of the XX Int. Students Day of Metallurgy, Chrakow, Poland, 2013
  • Proceedings
  • Materials and Production Engineering

Influence of coating on galling

A. Huskic, M. Kendel - Influence of coating on galling - XXX. Colloquium on metal forming , Planneralm, Austria, 2013, pp. 43-49
  • Proceedings
  • Materials and Production Engineering

Tool Life Studies of Generatively Produced Forging Tools

A. Huskic, J. Giedenbacher, A. Huskic, B. Behrens - Tool Life Studies of Generatively Produced Forging Tools - Forging , Vol. 92013, No. 3, 2013, pp. 66-70
Tools für forgings are currently manufactured by maching for the most part. In contrast, rapid tooling - the generative production of tools - could be used for…   mehr
  • Journal
  • Materials and Production Engineering

Direct Metal Laser Melting for Forming Tools

A. Huskic, J. Giedenbacher, U. Pschebezin, N. Wild, Z. Simicevic - Direct Metal Laser Melting for Forming Tools - XXX. Colloquium on metal forming , Planneralm, Austria, 2013, pp. 23-28
The use of selective laser melting (SLS) is becoming more and more widespread in toolmaking. One of the main advantages of this method is the production of…   mehr
  • Proceedings
  • Materials and Production Engineering

Comprehensive investigations of new filler materials for welding of high strength steels

R. Schnitzer, R. Rauch, W. Ernst, J. Wagner, S. Baumgartner, M. Leitner, M. Stoschka, T. Schlagradl, R. Schneider, C. Bernhard - Comprehensive investigations of new filler materials for welding of high strength steels - Proc. of the 3rd Int. Conf. on High Strength Steels for Hydropower Plants, Graz, Austria, 2013, pp. 323-332
  • Proceedings
  • Materials and Production Engineering

On the Austenite Stability of a New Quality of Twinning Induced Plasticity Steel, Exploring New Ranges of Mn and C

R. Mesquita, R. Schneider, K. Steineder, L. Samek, E. Arenholz - On the Austenite Stability of a New Quality of Twinning Induced Plasticity Steel, Exploring New Ranges of Mn and C - METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIAL S SCIENCE, Vol. 44, No. 9, 2013, pp. 4015-4019
Metallurgical and Materials Transactions A September 2013, Volume 44, Issue 9, pp 4015-4019 On the Austenite Stability of a New Quality of Twinning Induced…   mehr
  • Journal
  • Materials and Production Engineering

Effect of annealing parameters on microstructure and mechanical properties of phosphorus alloyed 16%Mn-TWIP steel

S. Hofer, K. Steineder, R. Schneider, M. Hartl, E. Arenholz, L. Samek - Effect of annealing parameters on microstructure and mechanical properties of phosphorus alloyed 16%Mn-TWIP steel - International Symposium on New Developments in Advanced High-Strength Sheet Steels Proceedings, Vail, Colorado, USA, United States of America, 2013, pp. 105-112
The present paper covers the effect of various solution/recrystallization-annealing temperatures on the mechanical properties such as yield strength, tensile…   mehr
  • Proceedings
  • Materials and Production Engineering

Comparison of Interfacial Shear Strength chraracterised using Fibre Debond and mechanical Testing in Polypropylene Basalt Fiber Composites

R. Zykaite, C. Burgstaller, B. Riedl, W. Stadlbauer - Comparison of Interfacial Shear Strength chraracterised using Fibre Debond and mechanical Testing in Polypropylene Basalt Fiber Composites - Advances in Polymer Science and Technology (APST) 3, Linz, Austria, 2013, pp. 1
  • Proceedings
  • Materials and Production Engineering

Influence of the Polarity on the Cleanliness Level and the Inclusion Types in the ESR Process

A. Paar, R. Schneider, P. Zeller, G. Reiter, S. Paul, P. Würzinger, I. Stiller - Influence of the Polarity on the Cleanliness Level and the Inclusion Types in the ESR Process - Proceedings of the 2013 International Symposium on Liquid Metal Processing & Casting, Austin, Texas, United States of America, 2013, pp. 29-36
  • Proceedings
  • Materials and Production Engineering

Modelling of damage mechanisms of short fibre reinforced polymers using X-ray CT

D. Salaberger, S. Oberpeilsteiner, J. Kastner, T. Koch, M. Palmstingl - Modelling of damage mechanisms of short fibre reinforced polymers using X-ray CT - Conference Materials Testing 2013, Neu-Ulm, Germany, 2013, pp. 217-222
This work deals with the characterization and modeling of fibers in short fiber reinforced polymers by means of X-ray computed tomography (XCT). Taking into…   mehr
  • Proceedings
  • Measuring and Testing Technolgy
  • Materials and Production Engineering

Developing the world of tooling

R. Schneider - Developing the world of tooling - International Heat Treatment and Surface Engineering, Vol. 7, No. 3, 2013, pp. 99-100
  • Journal
  • Materials and Production Engineering

Comparison of methods to determine fibre length distribution: X-ray CT versus standard method

D. Salaberger, S. Gleiß, J. Kastner - Comparison of methods to determine fibre length distribution: X-ray CT versus standard method - Int. Conf. Structural Analysis of Advanced Materials, Kos, Greece, 2013
For the determination of fibre length distribution of fibre reinforced polymers several methods are available. The standard method is burning or digesting the…   mehr
  • Proceedings
  • Measuring and Testing Technolgy
  • Materials and Production Engineering

Influence of flow channel surface on melt fracture and wall sliding behavior of a polypropylene melt

T. Bayer, G. Zitzenbacher, A. Giesbrecht, J. F. Pühringer, D. Vaught - Influence of flow channel surface on melt fracture and wall sliding behavior of a polypropylene melt - PPS-29 Conference Proceedings, Nürnberg (Deutschland) / Nuremberg (Germany), Germany, 2013
Polymer extrusion is widely used in the manufacture of plates or profiles. The quality of the extrudate is not only influenced by surface defect but even more…   mehr
  • Proceedings
  • Materials and Production Engineering

The influence of glass fibres on the longational viscosity studied by means of optical coherence tomography and X-ray computed tomography

M. Aigner, D. Salaberger - The influence of glass fibres on the longational viscosity studied by means of optical coherence tomography and X-ray computed tomography - PPS 29 Proceedings, Nürnberg (Deutschland) / Nuremberg (Germany), Germany, 2013
We report on the flow characteristics of glass-fiber-filled polymers in elongational rheometry. Unlike polymers with geometrically isotropic fillers,…   mehr
  • Proceedings
  • Measuring and Testing Technolgy
  • Materials and Production Engineering

Page 6 from 10
FH Oberösterreich Logo